Mounting A Tub
Mounting A Tub
Blog Article
They are making a few good points on Installing A Bathtub as a whole in this article followed below.
Mounting a bath tub isn't exactly brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately hard task. If the old tub is readily easily accessible, the task can move rapidly; if you need to open up a wall to remove the old tub and also place the brand-new bath tub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will need a helper to vacate the old bathtub and also set in the new one. Ensure you have actually certified on your own for the job and are comfortable attempting it. Rather than employing a service provider to take over a halfway-completed project, it is much better to take into consideration employing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This short article will certainly aid you install a new tub in your shower room if you have actually currently acquired a brand-new tub and don't need to alter the setup of your previous water pipes.
Your tools and material list must consist of the following:
Getting ready for the Setup
Firstly, the supporting framework supplied with the bath must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the flexible tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, activate the taps to drain any kind of water staying in the system. The process of getting rid of the existing faucets can be quite bothersome due to the limited gain access to that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth all set for the staying water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Before carrying on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, position the bathtub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub up until the level reads degree.
To mount taps, fit all-time low of the outermost flexible tap adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the supply of water and also check all joints and brand-new pipework for leakages and tighten them if required. Fill up the bath tub and likewise inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the tub needs to wait till the bathtub has been utilized at the very least when as this will certainly settle it into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap and the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin guaranteeing that the washers are in location between the faucet as well as the sink. Safeguard the faucet in position with the maker given backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The former type needs to be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to crack a rigid seal, creating the water to pass through the wall between the bath and also the tiling, causing issues with moisture and possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your fixtures and installations. They are offered in tubes as well as cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealant can split relatively early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles using waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a lot for taking time to read our post. If you please take the time to distribute this page if you liked it. I treasure reading our article about How to Install a Bathtub.
Schedule Service Pickup
Report this page